Piping Design Practical Training in Port Harcourt

Piping Design Practical Training in Port Harcourt

99% Practical Oriented Training
For contact and training venue in Port Harcourt call

Port Harcourt
IK Idegwue , Tel: 08032766980
Address: 71 Ada George Road, Port Harcourt

For further inquiry contact us:

Tel: +234 - 813 3476 558, +234 - 708 574 0887,
Opebi Allen Ikeja, Lagos State, Nigeria
Email: [email protected], [email protected]
Website: www.vogwconcept.com


COURSE OUTLINE

MODULE 1
1.0. Introduction to piping Design

• Piping engineering on the whole
• Piping design scope of work
• Basic concept and definitions
• Standard, codes and regulation
• Materials selection and specification
• Introduction to class and schedule
• Application of code/standard and selection
• Component of production system

1.1. Piping system

• Terminology
• Steel line
• Material specification
• Pipe manufacturing method
• Non metallic lines
  -Material specification
  -Joining methods
  - standard code, recommended practice
  -Design practice
  -Transmission, flow line, and distribution line
  -Manifolds
• Plant piping system
  -Designing loop system
  -Loop capacity and length
  -Equivalent diameter
  -Flow splitting and branch line
  -Complex liq and Gas gathering systems
  -offshore design Practices

Assignment and project work

MODULE 2
2.0 Application of Pressure Drop calculation in Design

• Bernoulli’s equation (When and how to use it)
• Darcy’s s equation (When and how to use it
• Reynolds’s number (When and how to use it)
• Liquid and Gas viscosity (When and how to use it)
• Relative roughness (When and how to use it)
• Frictional factor - equation and charts (When and how to use it)
• Z – factor correlation (When and how to use it)

2.1 Basic pressure equation

• General and empirical Hazen – Williams equation for liquids (When and how to use it)

• Isothermal, General, Weymouth and Panhandle equation General and empirical equation (When and how to use it)

• Approximate equations for small pressure drops (When and how to use it)
• Spitzglass equation for very low pressure line (When and how to use it)
• Fritzsch’s and Babcock equation for steam flow (When and how to use it)
• AGA, API RP 14 E and other empirical equations for 2- phase flow (When and how to use it)
• Application of pressure drop equations (When and how to use it
• Effects of elevation on pipeline pressure drop (When and how to use it)

2.2. Head Loss in valves and fitting

• Head loss in valves and fitting
• Resistance and flow coefficients

Equivalent length determination
2.3 Component of pipe connection

• Methods of pipe connections
• Fittings

Assignment and project work
MODULE 3
3.0. Line sizing determination

• Flow rate and surge factor consideration
• Pressure drop consideration
• Erosion velocity
• Single phase Liq and Gas line sizing
• 2- phase line sizing
• Multiphase line sizing

3.1. Wall Thickness determination

• Industrial standard and design code requirement
• General hoop stress formula
• ASME/ANSI, B31.3, B31.4, B31.8 equation
• Location class determination

3.2. Design procedures

• ANSI B16.6 and API 6A pressure rating
• Determination of pressure break
• Pipe, Valve and fitting types and specification
• Types of valves, materials and specification, class
• Types of fitting, materials and specification, class
• NPS, NB & OD of a pipe, National Pipe Thread Taper NPT

3.3. Piping system design
· Piping Layout
· Pipe support spacing
· Anchor blocks
· Manifolds
· Foundational integrity
· Piping vessel, heat exchanger and fire heaters
· Piping machinery
- Centrifugal and Reciprocating compressor
-centrifugal and reciprocating pump
-Gas engines and Turbines
· Data sheet specification
· Design of Buried steel Pipe
Assignment and project work

MODULE 4
4.0. Pipe stress calculation

• weight stress
• internal pressure stress
• Thermal Stress
• Expansion
• Pipe Dynamic
• Dynamic Load

4.1. Span Analysis calculation (Spacing for pipe support)
Types, code and specification

4.2. Relieve valves and pressure vacuum relief devices

• Relieving devices, application and consideration
• Relief valves sizing (Liq, Gas, oil)
• Pressure vacuum relief sizing
• Installation consideration
• Relief system piping design
• Venting consideration
• Application codes
• Standard and recommended practice

Assignment and project work
MODULE 5

5.0. Flare and vent disposal

• Back pressure consideration
• Applicable codes
• Flare and Vent piping systems

5.1. Fatigue analysis calculation- standard and code consideration
5.2. Hydro test and Leakage analysis calculation - standard and code consideration
5.3. Connecting point Load failure calculation (Nozzle load) - standard and code consideration

· Presentation of Result and Project reporting

• Project/ Case study

For contact and training venue in Port Harcourt call

IK Idegwue
Tel: 08032766980
71 Ada George Road, Port Harcourt

For further inquiry contact us:
Tel: +234 - 813 3476 558, +234 - 708 574 0887,
Opebi Allen Ikeja, Lagos State, Nigeria
Email: [email protected], [email protected]
Website: www.vogwconcept.com