Pipeline Design Practical Training in Port Harcourt

Pipeline Design Practical Training in Port Harcourt

99% Practical Oriented Training
For contact and training venue in Port Harcourt call

Port Harcourt
IK Idegwue , Tel: 08032766980
Address: 71 Ada George Road, Port Harcourt

For further enquiry contact us:

Tel: +234 - 813 3476 558, +234 - 708 574 0887,
Opebi Allen Ikeja, Lagos State, Nigeria
Email: [email protected], [email protected]
Website: www.vogwconcept.com

COURSE OUTLINE

MODULE 1
1.1 Pipeline engineering on the whole

• Pipeline design scope of work
• Basic concept and definitions
• Stages of pipeline projects
• Data Collection method for design
• Understanding what you need to execute your project at different stage
• Standard, codes and regulation
• Materials selection and specification
• Introduction to class and schedule
• Application of code/standard and selection
• Pipeline network and gathering system

1.2. Methods of pipe connections

• Fittings
• ANSI B16.6 and API 6A pressure rating
• Determination of pressure break

· Pipe, Valve and fitting types and specification
· Types of valves, materials and specification, class
· Types of fitting, materials and specification, class
· NPS, NB & OD of a pipe, National Pipe Thread Taper NPT

MODULE 2

2.0 Development and application of basic equation and factors

• Bernoulli’s equation (When and how to use it in pipeline design)
• Darcy’s s equation (When and how to use it in pipeline design)
• Reynolds’s number (When and how to use it in pipeline design)
• Liquid and Gas viscosity (When and how to use it in pipeline design)
• Relative roughness (When and how to use it in pipeline design)
• Frictional factor - equation and charts (When and how to use it in pipeline design)
• Z – factor correlation (When and how to use it in pipeline design)
• General and empirical Hazen – Williams equation for liquids (When and how to use it in pipeline design)

· Isothermal, General, Weymouth and Panhandle equation General and empirical equation (When and how to use it in pipeline design)

• Approximate equations for small pressure drops (When and how to use it in pipeline design)
• Spitzglass equation for very low pressure line (When and how to use it in pipeline design)
• Fritzsch’s and Babcock equation for steam flow (When and how to use it in pipeline design)
• AGA, API RP 14 E and other empirical equations for 2- phase flow (When and how to use it in pipeline design)
• Application of pressure drop equations (When and how to use it in pipeline design)
• Effects of elevation on pipeline pressure drop (When and how to use it in pipeline design)

2.1. Head loss in valves and fitting

· Resistance and flow coefficients
· Equivalent length determination
· Flow rate and surge factor consideration
· Pressure drop consideration
· Erosion velocity

MODULE 3

3.0 Line sizing determination
Single phase Liq and Gas line sizing
· 2- phase line sizing
· Multiphase line sizing
· Industrial standard and design code requirement
· General hoop stress formula
· ASME/ANSI, B31.3, B31.4, B31.8 equation
Location class determination

3.1. Pipe stress calculation
· Weight stress
· internal pressure stress
· Thermal Stress
· Expansion
· Pipe Dynamic
· Dynamic Load
· Span Analysis calculation (Spacing for pipe support)
Types, code and specification

MODULE 4

4.0 Pipeline Rout selection and overall Map

Types, code and specification
· On Bottom stability in pipe design
· Alignment sheet configuration
· Procedure and consideration for Buried and crossing
· Right of way consideration
· Road
· River
· Rail crossing
· Data sheet specification.

MODULE 5

5.0 Pipeline pigging

· Pipeline pigging –Objective, Types of pigging/size, pigging consideration during Construction, operation, maintenance, inspection, renovation, Design of pipeline pigging, Pig Launcher , Pig Traps and stations
· Relieve valves sizing (Liquid, Gas, Oil)
· Fatigue analysis calculation- standard and code consideration
· Flare and vent disposal
· Hydro test and Leakage analysis calculation - standard and code consideration
· Connecting point Load failure calculation (Nozzle load) - standard and code consideration
· Introduction to corrosion


· Presentation of Result and Project reporting

• Project work/Case study

For contact and training venue in Port Harcourt call

IK Idegwue
Tel: 08032766980
71 Ada George Road, Port Harcourt

For further enquiry contact us:
Tel: +234 - 813 3476 558, +234 - 708 574 0887,
Opebi Allen Ikeja, Lagos State, Nigeria
Email: [email protected], [email protected]
Website: www.vogwconcept.com