Affordable training for oil and gas industrty for corpers

ELDEMUZ ENGINEERING CONSULTING IS A registered LOCAL CONTENT PARTNER with the federal government of Nigeria IN CAPACITY DEVELOPMENT for the oil and gas industry. We offer training to, consultant, engineers, managers, senior and junior staff in the oil and gas industry as well as fresh graduates and focused undergraduates. Our interest is for those pursuing excellence and improvement in their career. Our work force is made up of young Nigerian engineering graduates who have acquired software skills through the PTDF scheme. Our goal is to transfer knowledge at its best. The software’s we offer are used mostly by SHELL, MOBIL, SCHLUMBERGER, TOTAL, ELF, AGIP AND other major oil companies in Nigeria.

Courses available

OIL & GAS PROCESS MODELING WITH ASPEN HYSYS(4weeks)

2.HYSYS DYNAMIC SIMULATION(4weeks)
3 PIPESIM-PIPELINE SIMULATION ,SURFACE AND SUB-SURFACE PIPING sim(4WEEKS)
4. Basic PIPING DESIGN,stress analysis AND PLANT LAYOUT TRAINING course(4weeks)
5. PLANT design AND STRESS ANALYSIS (PDMS & CAESARII)
(4weeks)
6. CAESARII-stress analysis(4weeks)
7. FULL PACKAGE AUTOCAD (2D, 3D&ISOMETRICS)(4weeks)
DETAILED TRAINING COURSE OUTLINE

1.OIL & GAS PROCESS MODELING WITH ASPEN HYSYS(4weeks)
scope
•Introduction to HYSYS
• Propane Refrigeration loop
• Refrigerated Gas Plant
• NGL Fractionation Train
• Oil Characterization
• Gas Gathering
• Two-Stage Compression
• Acid Gas Sweetening with DEA
• Natural Gas Dehydration with TEG
Process Plant Costing
• Reporting in Aspen HYSYS

2.HYSYS DYNAMIC SIMULATION(4weeks)
The dynamic simulation specifically handles EQUIPMENT sizing and process control
1. REVISION OF STEADY STATE
2. BASIC CONTROL THEORY
3. PRESSURE-FLOW RELATIONSHIP
4. TRANSITIONING FROM STEADY STATE TO DYNAMICS-MODYFYING THE STEADY STATE
5. SIZING UNIT OPERATIONS (DE-PROPANIZER COLUMN, SEPERATORS etc)
6. USING THE DYNAMICS ASSISTANT AND ACTIVATING THE DYNAMIC MODE
7. INSTALLING THE CONTROLLERS (PID)
8. SETTING UP STRIP CHARTS
9. RUNNING AND MONITORING DYNAMIC SIMULATION.
10. ADVANCED DYNAMICS

3. PIPESIM-PIPELINE SIMULATION ,SURFACE AND SUB-SURFACE PIPING sim
COURSEOUTLINE
1.INTRODUCTION
2.SINGLE PHASE FLUID MODELING-WATER,GAS OIL
3.WELL PERFORMANCE MODELING.
4.ARTIFICIAL LIFT DESIGNS.
5.SINGLE BRANCH PIPELINE AND FACILITIES
6.NETWORK MODELLING-

4.Basic PIPING DESIGN,stress analysis AND PLANT LAYOUT TRAINING course(8weeks)
(3-softwares are to be used here-autocad,pdms,caesarII)
1.Plant layout fundamentals and work flow procedures
2• Terminology and symbols used in plant layout
3• Plot plans, elevations and 3-D models
4• Fundamental principles of chemical process technology
5• Process flow diagrams (PFDs)
6• Equipment used in process plants
7• Instrument symbols and abbreviations
8• Piping and instrumentation diagrams (P&IDs)
9• Piping design and engineering principles
10• Terminology, symbols and abbreviations used in piping design
11• Piping materials
12• Piping specifications and piping codes
13• Components of piping systems - fittings, flanges and valves
14• Piping isometrics and bill of materials

5.PLANT design AND STRESS ANALYSIS (PDMS & CAESARII)
PDMS SCOPEs.(4weeks or 70hrs )
A. Equipment DESIGN (vessels, pumps, heat exchanger, assemblies, air coolers)
B. Piping DESIGN INCLUDING explicit piping for piping engineers
C. Structural steelwork (column, beams, panels and plates, wall and floors)for civil
And structural engineers
D. ASL MODELLER (Access, stairs and ladder) for structural and civil engineers
E. Cable trays for electrical and electronics &instrument engineers
2. Production of MTO’s and piping general assembly
3. Conversion from PDMS Draft & Isodraft to AutoCAD format.
4. Customizing PDMS
5. Plant layout and drafting interpretation
6. Using ASME code
The training will be based on ASME B31.3 &B31.4 CODE.
At the end of the training, a PILOT project on modeling of an liquefied petroleum gas plant (COOKING GAS PLANT) will be carried out by the trainee.

6.CAESARII SCOPE(4weeks)

1. Basic functions of a pipe stress engineer, with emphasis on the relationship between the discipline and piping design.
2. Sources and solutions to piping stress related problems.
3. Pipe support standards.
4. Introduction to stress analysis
5. Setting pipe models for stress analysis
6.analysis on pumps.
7. Analysis
7.FULL PACKAGE AUTOCAD (2D, 3D&ISOMETRICS)(4weeks)

COURSE CONTENT-2D DRAFTING & 3D MODELLING
a. AutoCAD general
b. AutoCAD mechanical
c. AutoCAD PID, piping and instrumentation design.
D. AutoCAD structural /architectural.
AUTOCAD 2D DRAFTING
B. AUTOCAD MECHANICAL
1. DESIGN OF BASIC MECHANICAL COMPONENTS.(BOLTS,NUTS,FLANGES,E.T.C
2. INTERPRETATION OF METRIC AND IMPERIAL STANDARDS.AND DESIGN IMPLICATIONS.
3. Machine drawing
C. AUTOCAD PIPING.
1. PIPE DRAFTING AND DESIGN (PIPE ISOMETRICS, DOUBLE AND SINGLE LINE DRAFTING)
2.PIPING AND INSTRUMENTATION DIAGRAMS (P&ID),
4.PROCESS FLOW DIAGRAMS/SHEETS (PFD/PFS)
D.AUTOCAD CIVIL/STRUCTURAL/
1. House plan and elevations
2. BEAMS AND COLUMN DESIGN
3. SLAB DESIGN
AUTOCAD 3D MODELLING,
1. Introduction to 3d fundamentals-BASIC TOOLS (MODELING TOOL,SOLID EDITING,VIEWS,VISUAL STYLES ,3D MODIFY)
2. Modeling of structures (houses, PLATFORMS etc.)
3. Modeling of mechanical parts and components i.e. mechanical coupling
4. Modeling of piping components (elbows, tees, flange, reducer, valves, etc.) FOR 3D PIPING
5. DESIGN OF EQUIPMENTS (, pumps, pressure vessels, heat exchangers, e.tc)
6. Project and assessment

Training Date: batch dates -6^th – 26^th January, 13^th January – 6^th February, 3^rd February – 24^th February, 26^th February – 10^th march, 4^th march – 29^th march, 30^th march – 26^th April, 6^th April – 29^th april,2014.
ALL Training is ALSO AVAILABLE weekends,WEEKDAYS and private schedule all through the year

Venue-Eldemuz Engineering Training centre.
First floor,60 Aba road by craft centre bus stop, (beside the pedestrian bridge)
Portharcourt.
info @eldemuz.com,[email protected]
08038812638,07051852201.